Vacuum Filtration with a Buchner Funnel: Setup, Equipment and Tips
Quick answer: To set up vacuum filtration, clamp a Buchner flask securely, fit a Buchner funnel into its neck with a rubber adapter, and connect the side arm to a vacuum source such as a water jet vacuum pump. Place a filter paper flat over the holes in the funnel, wet it with a little solvent, turn on the vacuum and pour in your mixture. When you finish, release the vacuum at the flask before turning off the pump.
Vacuum filtration (also called suction filtration) separates solids from liquids much faster than gravity filtration. It is the standard way to collect crystals and precipitates in chemistry, teaching, food and quality control labs. This guide covers the equipment you need, how to choose filter paper, a step-by-step setup and how to fix common problems.
What is vacuum filtration?
In vacuum filtration, a pump lowers the pressure inside a sealed flask. Air pressure then pushes the liquid through a filter paper in a Buchner funnel, leaving the solid behind on the paper. Because the liquid is pulled through rather than dripping under gravity, filtration is faster and the solid comes out drier.
Equipment you need
| Item | What it does | ANPROS options |
|---|---|---|
| Buchner funnel (porcelain) | Holds the filter paper on a flat, perforated plate | 50 mm to 250 mm diameter |
| Buchner flask | Thick-walled flask with a side arm that collects the filtrate under vacuum | 100 mL to 5000 mL, including 1000 mL with a 24/29 joint |
| Rubber adapter (Gooch) | Seals the funnel into the flask neck so the system holds a vacuum | 41 x 29 mm |
| Water jet vacuum pump | Creates a vacuum from tap water flow, with no electric pump needed | Plastic, corrosion resistant |
| Filter paper | Traps the solid | 90, 150 and 185 mm; grades MS1 to MS4 and Economy No. 1 |
| Thick-walled vacuum tubing, retort stand and clamp | Connect the pump and hold the flask steady | Retort stands and clamps available |
Want everything in one box? The Buchner filtration kit includes a 500 mL Buchner flask, a 90 mm porcelain Buchner funnel, a plastic water jet vacuum pump, a 41 x 29 mm Gooch rubber adapter and 90 mm wet-strength filter paper.
How to choose filter paper
Choose the fastest filter paper that still traps your solid. Coarse precipitates can use a fast paper; fine crystals need a slower paper with smaller pores.
| ANPROS grade | Equivalent | Speed | Particle retention | Best for |
|---|---|---|---|---|
| MS1 | Whatman No. 4 | Fast | About 20 microns | Coarse precipitates |
| MS2 | Whatman No. 1 | Medium | About 5–10 microns | Medium crystalline solids |
| MS3 | Whatman No. 2 | Medium to slow | About 5–8 microns | Medium crystalline solids |
| MS4 | Whatman No. 6 | Slow | Below 5 microns | Fine crystalline solids |
| Economy No. 1 | General purpose | Medium | About 5–10 microns | Routine filtration |
Size: the paper should lie flat and cover all the holes in the funnel plate without curling up the sides. Strength: under vacuum, use wet-strengthened filter paper so it doesn't tear.
How to set up vacuum filtration: step by step
- Check the glassware. Look for cracks, chips or scratches on the Buchner flask. Only use flasks designed for vacuum.
- Clamp the flask. Clamp the Buchner flask to a retort stand by the neck so it can't tip over.
- Connect the vacuum. Attach thick-walled tubing from the flask's side arm to the water jet pump (ideally through a trap flask, which stops liquid being sucked back into the line).
- Fit the funnel. Push the Buchner funnel into the rubber adapter in the flask neck to form an airtight seal.
- Add the filter paper. Place the paper flat in the funnel so it covers every hole.
- Wet the paper. Moisten the paper with a little of the same solvent you are filtering, then switch on the vacuum. The paper should pull down flat and seal.
- Filter. Swirl the mixture and pour it into the centre of the funnel. Rinse the last of the solid in with a little solvent.
- Wash the solid. Add a small amount of cold solvent to wash the solid, letting the vacuum pull it through.
- Dry the solid. Leave the vacuum running for a few minutes to pull air through and dry the solid.
- Release the vacuum first. Disconnect the tubing at the flask (or open the vent) before you turn off the water. Otherwise water can be sucked back into your flask.
Using a water jet vacuum pump
A water jet vacuum pump (also called a water aspirator) attaches to a laboratory tap. Water flowing through the pump creates suction, so no electrical power is needed. The ANPROS plastic water jet pump is corrosion resistant and fits standard laboratory tubing. The vacuum it reaches depends on your water pressure.
- Turn the tap on fully for the strongest vacuum.
- Always break the vacuum before turning the water off, to prevent suck-back.
- Water jet pumps are also used for distillation and aspiration setups.
Troubleshooting vacuum filtration
| Problem | Likely cause | What to do |
|---|---|---|
| Weak or no suction | Leak at the funnel adapter or tubing, or low water pressure | Reseat the funnel in the adapter, check the tubing connections, turn the tap fully on |
| Solid passes through into the flask | Paper too coarse, not covering all holes, or torn | Use a slower grade (for example MS3 or MS4), make sure the paper lies flat, and use wet-strength paper |
| Filtration is very slow | Paper too fine for the solid, or the paper is clogged | Try a faster grade (for example MS1 or MS2) or a larger funnel |
| Water in the flask after switching off | Pump turned off before the vacuum was released | Next time, disconnect the tubing or vent the flask first; use a trap flask |
| Paper lifts or curls | Paper too large or not wetted | Use a paper that fits the funnel plate and wet it before pouring |
Safety tips
- Never use a thin-walled flask (such as a standard conical flask) under vacuum. It can implode.
- Clamp the flask, and inspect glassware before every use.
- Wear safety glasses, and work in a fume cupboard when filtering volatile or hazardous liquids.
- Follow the safety data sheet for every chemical you filter.
Frequently asked questions
What is a Buchner funnel used for?
A Buchner funnel is used with a Buchner flask and a vacuum source to separate solids from liquids quickly, for example to collect crystals or a precipitate.
What is the difference between a Buchner flask and a conical flask?
A Buchner flask has thick walls and a side arm for a vacuum connection, so it can safely be used under reduced pressure. A standard conical flask isn't designed for vacuum.
What size filter paper do I need for a Buchner funnel?
Use a paper that lies flat and covers all the holes in the funnel plate without curling up the sides. ANPROS filter paper comes in 90, 150 and 185 mm.
Which filter paper grade is best for fine precipitates?
A slow grade with small pores, such as MS4 (equivalent to Whatman No. 6), retains particles below about 5 microns.
Do I need an electric vacuum pump?
Not always. A water jet vacuum pump creates a vacuum from tap water flow and is common in teaching and routine labs.
Why should I release the vacuum before turning off the water?
If you turn off a water jet pump while the flask is still under vacuum, water can be sucked back into the flask and contaminate your filtrate.
Where can I buy vacuum filtration equipment in Australia?
ANPROS in Boronia, Victoria supplies porcelain Buchner funnels, Buchner flasks, Gooch rubber adapters, water jet vacuum pumps, filter paper and complete Buchner filtration kits.
Buy vacuum filtration equipment from ANPROS
Browse the full laboratory filtration range, including Buchner filtration kits and syringe filters, or contact the ANPROS team for help choosing the right setup.




